|
TECHNICAL DATA SHEET
Eggshell Finish
A top quality latex paint designed for professionals that combines
the beauty of an eggshell-like finish and the durability of a semi-gloss.
RXM Eggshell Finish has excellent hiding characteristics and is
easy to apply, spatter resistant, washable and non-yellowing.
RECOMMENDED USES
Can be used on interior trim, doors, cabinets, walls and ceilings.
Recommended for new or previously painted or textured surfaces including
drywall, wallboard, wood, plaster, masonry and metal.
PRODUCT FEATURES
o Pleasing eggshell sheen
o Formulated for easy stain removal
o Durable finish
o Washable
o High hiding
o Stain resistant
o Easy to apply
o Filtered for airless spraying
o Self priming
o Low odor
o Resists mold and mildew
o Designed for professionals
o Resists peeling
o Resists cracking
o Soap and water cleanup
o Excellent color retention
o Laboratory tested
o Nonflammable
o Water base
o Environmentally safe
o Made in USA
o Non-Photochemically Reactive
SURFACE PREPARATION
Surfaces to be coated must be clean, dry, and free of wax, grease,
dust, mildew, water soluble
materials, and scaling paint. Glossy areas should be dulled. New
masonry surfaces must be allowed to cure (30-60 days) before priming.
All masonry surfaces must be thoroughly brushed with stiff fiber
bristles to remove loose particles.
Difficult Substrates: TM Pratt & Company offers a number of
specialty primers for use over difficult
substrates such as bleeding woods, grease, crayon markings, hard
glossy substrates where paint
adhesion or stain suppression is a particular problem. TM Pratt
& Company can recommend the right problem-solving primer for
your special needs.
PRIMER/FINISH SYSTEMS
Apply primer coat before and after filling nail holes, cracks, and
other surface imperfections. For best results when a significant
color change is required, use a primer tinted to the approximate
finish coat color.
Wood, Plaster/Drywall, Smooth Concrete/Masonry, Unpainted:
Primer: RXM Primer
Finish: 1 or 2 coats RXM Eggshell Finish
Wood, Plaster/Drywall, Smooth Concrete/Masonry, Repaint:
Primer: Prime or spot prime as needed with RXM Eggshell Finish
Finish:1 or 2 coats RXM Eggshell Finish
Rough or pitted masonry, Unpainted:
Primer: RXM SA Primer followed by RXM Skim Coat
Finish: 1 or 2 coats RXM Eggshell Finish
Metal, Unpainted:
Primer: Metal Primer
Finish: 1 or 2 coats RXM Eggshell Finish
APPLICATION
Mixing of Paint: Stir thoroughly before and occasionally during
use. Apply in full even coats with a quality synthetic bristle brush,
short to medium nap roller, pad, or spray. Never add other paints,
oil colors, or solvents to this product.
Spray, Conventional: See thinning/Cleanup on next page.
Spray, Airless: Fluid Pressure - 1,500 to 2,000 PSI; Tip - .017
Orifice; Filter - 50 mesh
COVERAGE
190-250 sq. ft. (17.6-23.2 sq. meters) per gallon. Depending on
previous color, surface porosity, texture, and application methods
coverage can vary greatly.
TECHNICAL DATA
Finish: Eggshell
Color: White and custom tinting at factory to users specifications.
Vehicle Type: Proprietary Blend of Acrylic Latexes
Pigment Type: Titanium Dioxide
Dries By: Evaporation, Coalescence
Viscosity: 97KU
Weight Per Gallon: 10.9 pounds
Specific Gravity: 1.31
Weight Solids: 49.0%
Volume Solids: 33.6%
% Vehicle by Weight: 68.3%
% Vehicle by Volume: 86.6%
% Pigment by Weight: 29.8%
% Pigment by Volume: 11.1%
% Solvent by Weight: 51.0%
% Solvent by Volume: 66.4%
% Vehicle Solids by Weight: 17.3%
% Vehicle Solids by Volume: 20.2%
Theoretical Coverage at Recommended Film Thickness: 190-250 sq.
ft. per gallon
Wet Film Thickness: 7.3 mils
Dry Film Thickness: 2.4 mils
60º Specular Gloss: Eggshell
Surface Application Temperature:
Min. 50ºF.; Max. 90º F.
Thin With: Clean Water
Clean Up Thinner: Clean Water
Flash Point (Seta): None
V.O.C.: (Material) 46 g/l; .38 lb/gal
V.O.C.: (Coating) 120 g/l; 1.00 lb/gal
DRYING TIME
Dry Time @ 77 F (25C) @ 50% RH
Set To Touch - 2 Hours
To Handle - 4 Hours
To Recoat - 12 Hours
Drying times may vary depending on temperature, humidity and air
movement.
THINNING/CLEANUP
Thinning is unnecessary, but if required to obtain desired application
properties, a small amount of clean water may be added. Never add
other paints or solvents. Clean hands, tools and equipment promptly
with warm soapy water. Spray equipment should be given a final rinse
with mineral spirits to prevent rusting. USE COMPLETELY OR DISPOSE
OF PROPERLY. Dry, empty containers may be recycled in a can recycling
program. Local disposal requirements vary; consult your sanitation
department or statedesignated environmental agency for information
on disposal options.
CERTIFICATION
Formulated without lead or mercury
STORAGE
Twelve month shelf life if containers are sealed, upright and stored
in a dry place. Maintain temperatures between 45 and 100 degrees
F. Skins formed on surface must be removed prior to moving, mixing
or using.
LIMITATIONS
Do not apply when air and surface temperatures are below 50ºF
(10ºC).
TECHNICAL ASSISTANCE
For further technical assistance contact TM Pratt & Company.
CARE OF FRESH FINISH
Avoid washing for 7 days. Once cured, dirt and stains can be removed
with a mild (non-abrasive)
detergent and water.
PRODUCT AVAILABILITY
Available in five (5) gallon containers weighing 56.6 pounds. Can
be factory custom tinted to virtually any color.
ENVIRONMENTAL/SAFETY
Use only with adequate ventilation. Do not breathe spray mist or
sanding dust. Avoid contact with eyes and prolonged or repeated
contact with skin. Wear eye protection and gloves during application
or sanding. A dust/particulate respirator approved by NIOSH should
be worn when sanding or spraying. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the
area to obtain fresh air.
IN CASE OF SPILL: Absorb with inert material and dispose of as specified
under Thinning/Cleanup.
Hazardous Materials Identification System ® NPCA:
Health - 1
Flammability - 0
Reactivity - 0
Personal protection -
0=Minimal; 4=Severe Hazard
Material safety data sheets available on request from TM Pratt &
Company.
CAUTION
KEEP OUT OF REACH OF CHILDREN o PROTECT FROM FREEZING o DO NOT TAKE
INTERNALLY
LIMITED WARRANTY
In lieu of all other warranties or guarantees, express or implied
by contract or law, manufacturer's liability is hereby limited to
replacement of such quantities of this material if found to be defective.
Manufacturer shall not be liable for any representation, warranties
(express or implied) made by any of its agents, representatives
or employees or by any applicator regarding the product contained
herein. In no case will manufacturer reimburse for extra labor cost
or be responsible for damage or replacement of substrates to which
this product is applied. Contact company for a complete description
of limited warranty.
|
